지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 발행연도
- 2011.12
- 수록면
- 128 - 133 (6page)
이용수
초록· 키워드
오류제보하기
In this study, the steel material for shipbuilding(LR-A class) was used, and FCAW was taken advantage of 3G attitude and they are welded by different welding ways. As a result of analyzing wave with welding monitoring system, the stable values are obtained which are the first floor(electronic current 164~182 A, voltage 24 V), the second floor(electronic current 174~190 A, voltage 22~25 V), the third floor(electronic current 158~188 A, voltage 22~25 V), and fourth floor(electronic current 172~184 A, voltage 22~25 V), at this time, the stable wave standard deviation and changing coefficient could be obtained.
When the welding testing through nondestructive inspection was analyzed know defect of welding, there was no defect of welding in A, D, E, but some porosities in B, and slag conclusion near the surface in C, because the length of arc was not accurate, and the electronic current and voltage was not stable. After observing the change of heat affect zone through micro testing, each organization of floor formed as Grain Refinement, so welding part was fine, the distance of heat affect zone is getting wider up to change the values of the electronic current and voltage. As a result of degree of hardness testing, the hardness orders were the heat affect zone(HAZ), Welding Zone(WZ), and Base Metal(BM). When the distribution of degree of hardness is observed. B is the highest degree of hardness The reason why heat effect zone is higher than welding zone and base metal, welding zone is boiled over melting point(1539℃) and it starts to melt after the result of analysis through metal microscope, so we can know that delicate tissue is created at the welding zone. Therefore, in order to get the optimal conditions of the welding, the proper current of the welding and voltage is needed. Furthermore the precise work of welding is required.
When the welding testing through nondestructive inspection was analyzed know defect of welding, there was no defect of welding in A, D, E, but some porosities in B, and slag conclusion near the surface in C, because the length of arc was not accurate, and the electronic current and voltage was not stable. After observing the change of heat affect zone through micro testing, each organization of floor formed as Grain Refinement, so welding part was fine, the distance of heat affect zone is getting wider up to change the values of the electronic current and voltage. As a result of degree of hardness testing, the hardness orders were the heat affect zone(HAZ), Welding Zone(WZ), and Base Metal(BM). When the distribution of degree of hardness is observed. B is the highest degree of hardness The reason why heat effect zone is higher than welding zone and base metal, welding zone is boiled over melting point(1539℃) and it starts to melt after the result of analysis through metal microscope, so we can know that delicate tissue is created at the welding zone. Therefore, in order to get the optimal conditions of the welding, the proper current of the welding and voltage is needed. Furthermore the precise work of welding is required.
목차
ABSTRACT
1. 서론
2. 이론적 배경
3. 실험장치 및 조건
4. 실험결과 및 고찰
5. 결론
참고문헌
참고문헌 (7)
참고문헌 신청
1. [보고서] - S. Adolfsson / 1999 / On-Line Quality Monitoring in short-circuit gas metal Arc Welding : 59 ~ 73
2. [보고서] - T.P. Quinn / 1999 / Arc Sensing for Defects in Constant-Voltage Gas Metal Arc Welding : 322 ~ 328
3. [학술지(정기간행물)] - ANON / 1984 / Self-Shielded FCAW Speeds High-Rise Constrution / Welding Journal 63 (4) : 47 ~ 49
4. [학술지(정기간행물)] - ANON / 1986 / Office Building Columns Field Spliced with Self-Shielded Welding Wire / Welding Journal, Welding Journal 65 (10) : 53 ~ 54
5. [학술지(정기간행물)] - S. M. Cho / 1998 / A Study on the Quantitative Evaluation of Stabilityin AC SMAW / Journal of KWS 16 (4) : 125 ~ 131
2. [보고서] - T.P. Quinn / 1999 / Arc Sensing for Defects in Constant-Voltage Gas Metal Arc Welding : 322 ~ 328
3. [학술지(정기간행물)] - ANON / 1984 / Self-Shielded FCAW Speeds High-Rise Constrution / Welding Journal 63 (4) : 47 ~ 49
4. [학술지(정기간행물)] - ANON / 1986 / Office Building Columns Field Spliced with Self-Shielded Welding Wire / Welding Journal, Welding Journal 65 (10) : 53 ~ 54
5. [학술지(정기간행물)] - S. M. Cho / 1998 / A Study on the Quantitative Evaluation of Stabilityin AC SMAW / Journal of KWS 16 (4) : 125 ~ 131
이 논문의 저자 정보
이 논문과 함께 이용한 논문
조선의 용접자동화 응용
한용섭
산업공학 (IE interfaces)
1995
.07
원전배관 협계용부 파괴인성 시험을 위한 소성 η계수
허용
,
조성근
,
구재민
외 1명
대한기계학회 춘추학술대회
2007
.10
고속차량을 위한 냉각팬용 인버터 시스템
김영춘
,
조문택
,
김옥환
외 2명
대한전기학회 학술대회 논문집
2016
.07
심용접에 의한 판재로 보강된 균열판의 응력세기계수 해석 ( Analysis of Stress Intensity Factor for the Cracked Plate Reinforced with a Sheet by Seam Welding )
김옥환
,
박성두
,
이영호
대한용접·접합학회지
1998
.02
아크용접 품질 모니터링 기술의 최신 국내 연구 동향
김영민
,
천현필
대한용접·접합학회지
2023
.04
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2013-581-001375021