지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 발행연도
- 2012.12
- 수록면
- 1,018 - 1,023 (6page)
이용수
이 논문의 연구 히스토리 (3)
2012
- 이 논문의 후속연구가 궁금하신가요?
- 연관 학술논문 또는 학술발표를 통해 보다 발전된 연구결과를 확인하실 수 있습니다.
- 이 논문의 연구 히스토리 확인하기
초록· 키워드
오류제보하기
In order to substitute and recycle the existing automobile parts for GMT-sheet, researches on the effects of GMT-sheet on the establishment of precise joining strength, joining condition that are lap length of joining part, compression ratio, and closure speed must be carried out but until now. Besides, many researches on adhesion joint had been conducted until now but no systematic research on press lap joint of GMT-sheet has been implemented until recently and the reliability of joining strength is not yet established. In press lap joining molding of GMT-sheet, tensile stress and lap joining connection efficiency was increased according to the increase of lap length L. However, as the increase of compression ratio and fiber content ratio per unit area was higher in tensile test, it has caused the deterioration of lap joining efficiency after joining molding of GMT-sheet. Clarify joining strength and lap joining efficiency during high temperature compression press lap joining molding of GMT-sheet and research data regarding to the lap length of joining part was presented. The purpose of this study is to contribute to the substitution of existing products as well as usage development in non-automobile field and also to find out precise dynamic characteristics as designing data of structures.
목차
1. Introduction
2. Theory
3. Test Results and Discussion
4. Conslusions
ACKNOWLEDGMENT
REFERENCES
참고문헌 (9)
참고문헌 신청
1. [학술지(정기간행물)] - Kim, J. W / 2011 / Creep and tensile properties of press molding joined GMT-sheets / TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA 21 : 170 ~ 174
3. [학술지(정기간행물)] - Kim, J. W / 2008 / Measurement of Fiber Orientation Angle in FRP by Intensity Method / Journal of Materials Processing Technology 201 (1-3) : 755 ~ 760
5. [학술지(정기간행물)] - 이동기 / 201005 / Effect of Fiber Orientation and Fiber Contents on the Tensile Strength in Fiber-Reinforced Composites / JOURNAL OF NANOSCIENCE AND NANOTECHNOLOGY 10 (5) : 3650 ~ 3653
6. [학술지(정기간행물)] - Kim, J. W / 2011 / Study on Fibre Orientation of Weld Line Parts during Injection Moulding of Fiber Reinforced Plastic by Image Processing / Materials Research Innovations 15 (1) : 303 ~ 306
7. [학술지(정기간행물)] - Kim, J. W / 2012 / Effect of Molding Condition on Arithmetical Average Roughness of GMT-sheet Moldings / Advanced Science Letters 8 : 682 ~ 686
3. [학술지(정기간행물)] - Kim, J. W / 2008 / Measurement of Fiber Orientation Angle in FRP by Intensity Method / Journal of Materials Processing Technology 201 (1-3) : 755 ~ 760
5. [학술지(정기간행물)] - 이동기 / 201005 / Effect of Fiber Orientation and Fiber Contents on the Tensile Strength in Fiber-Reinforced Composites / JOURNAL OF NANOSCIENCE AND NANOTECHNOLOGY 10 (5) : 3650 ~ 3653
6. [학술지(정기간행물)] - Kim, J. W / 2011 / Study on Fibre Orientation of Weld Line Parts during Injection Moulding of Fiber Reinforced Plastic by Image Processing / Materials Research Innovations 15 (1) : 303 ~ 306
7. [학술지(정기간행물)] - Kim, J. W / 2012 / Effect of Molding Condition on Arithmetical Average Roughness of GMT-sheet Moldings / Advanced Science Letters 8 : 682 ~ 686
이 논문의 저자 정보
이 논문과 함께 이용한 논문
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2014-552-000676522