지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
이용수
이 논문의 연구 히스토리 (2)
- 이 논문의 후속연구가 궁금하신가요?
- 연관 학술논문 또는 학술발표를 통해 보다 발전된 연구결과를 확인하실 수 있습니다.
- 이 논문의 연구 히스토리 확인하기
초록· 키워드
오류제보하기
As an advance study for the development of a heat sink for special purpose high power illumination, an investigation was made to find feasibility for the application of copper plated EP to a heat sink of small LED light of less than 10W installed in commercial product. In this study, the plated heat sink with EP copper was fabricated for the conventional LED light. It was used actually for finding heat radiation property and effectiveness of the heat sink accompanied with measurement of luminous intensity. The heat is radiated by transfer and dissipation only through the copper plated surface due to extremely low heat conductivity of EP in case of EP heat sink; however the total area of the plate plays the function of heat transfer as well as heat radiation in case of the aluminum heat sink. It seems that the volume difference of heat radiating material is so big that the temperature P₁ is 9.0~12.3% higher in 3W and 42.7~54.0% higher in case of 6W volume difference of heat radiating material is so big that the temperature P₁ is 9.0~12.3% higher in 3W and 42.7~54.0% higher in case of 6W even though heat transfer rate of copper is approximately 1.9 times higher than that of aluminum. It was thought that this is useful to utilize for heat sink for low power LED light with the low heating rate. Also, the illumination could be greatly influenced by the surrounding temperature of the place where it is installed. Therefore, it seems that the illumination installation environment must be taken into consideration when selecting illumination. Further study was expected on order to aims at development of an exterior surface itself made into heat radiation plate by application of this technology in future.
목차
ABSTRACT
1. 서론
2. LED 조명 기술
3. 동 도금 EP방열판의 방열 테스트
4. 실험 결과 및 고찰
5. 결론
REFERENCES
참고문헌 (9)
참고문헌 신청
1. [보고서] - Yoo, J. Y / 2005 / Patent technology Trends of LED Heat Radiation Technology
2. [학술대회논문] - Kim, G. H / 2008 / A Study on the Micro-cutting Process Characteristics of Copper for Manufacturing a Subminiature Radiation Plate / Proceedings of the KSMTE Spring Conference 2008 : 296 ~ 301
3. [학위논문] - Lee, K. Y. / 2007 / A Study on the Performance Enhancement of Heat Sink Using Heat Pipe / 석사 / Pukyong National University
4. [기타자료] - Bruce S. / 2003 / Technologies that Deserve to Die / MIT's Technology Review
5. [기타자료] - / 2002 / Light Emitting Diodes(LEDs) for General Illumination / OIDA Technology Roadmap
2. [학술대회논문] - Kim, G. H / 2008 / A Study on the Micro-cutting Process Characteristics of Copper for Manufacturing a Subminiature Radiation Plate / Proceedings of the KSMTE Spring Conference 2008 : 296 ~ 301
3. [학위논문] - Lee, K. Y. / 2007 / A Study on the Performance Enhancement of Heat Sink Using Heat Pipe / 석사 / Pukyong National University
4. [기타자료] - Bruce S. / 2003 / Technologies that Deserve to Die / MIT's Technology Review
5. [기타자료] - / 2002 / Light Emitting Diodes(LEDs) for General Illumination / OIDA Technology Roadmap
이 논문의 저자 정보
이 논문과 함께 이용한 논문
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2014-580-002441194