지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 발행연도
- 2013.12
- 수록면
- 458 - 465 (8page)
이용수
이 논문의 연구 히스토리 (2)
- 이 논문의 후속연구가 궁금하신가요?
- 연관 학술논문 또는 학술발표를 통해 보다 발전된 연구결과를 확인하실 수 있습니다.
- 이 논문의 연구 히스토리 확인하기
초록· 키워드
오류제보하기
Ship design engineering refers to the development and design of shipbuilding architectures in a drawing which reflects all relevant manufacturing processes. This paper provides analysis methods for model-information interfaces between hull structure design and outfitting design, and a technical application for manufacturing phases reflecting the pipe support pad and angle item automatically. The existing information procedure of pipe support pad and angle system processes information using drawing without model specification. Outfitting design team directly distributes drawings to the shop floor then manual-based marking and installation work are conducted refer to the distributed drawings. As a result, this process has become time consuming and causes problems in the productivity and quality improvement due to the rework caused by omitted or incorrect marking. The pipe support pad and angle marking is a method that automatically updates model information to hull structure design using sets of data that analyse the generated model in outfitting design processes. Therefore, this approach provides an efficient solution through design references without manual activities such as a reflection of hull structure design, cutting process, numerical control work, and dimension measurement and marking. The conversion of a method from the existing procedure based on manual marking to the reflective and automatic approach would have enabled to proceed installation work without manual activities for the measurement. Therefore, this research study proposes an efficient approach using pre-data analysis of model information interfaces between design and manufacturing phases to improve productivity during construction for shipbuilding.
목차
1. 서론
2. 관련분야 연구현황
3. 정보인터페이스 기반 프로세스
4. 시스템 구현
5. 결론
References
참고문헌 (7)
참고문헌 신청
1. [학술대회논문] - Kim, H.C. / 2004 / Hole plan @ DSME based on tribon mx / Aveva Marine Korea User Group Meeting 2004
2. [학술지(정기간행물)] - Park, J.H. / 2010 / Shipbuilding IT Status and Prospects / Electronics and Telecommunications Trends 25 (4) : 19 ~ 26
3. [보고서] - Park, H.Y. / 2008 / Development of the E/R Insulation Modeling Automation System Using Structural Hull Model Information : 112 ~ 117
5. [학술지(정기간행물)] - 유원선 / 2012 / The implementation of the integrated design process in the hole-plan system / International Journal of Naval Architecture and Ocean Engineering 4 (4) : 353 ~ 361
6. [학술지(정기간행물)] - Suh, H. W. / 2004 / Development of IT based Concurrent Collaboration System / Bulletin of the Society of Naval Architects of Korea 41 (3) : 27 ~ 36
2. [학술지(정기간행물)] - Park, J.H. / 2010 / Shipbuilding IT Status and Prospects / Electronics and Telecommunications Trends 25 (4) : 19 ~ 26
3. [보고서] - Park, H.Y. / 2008 / Development of the E/R Insulation Modeling Automation System Using Structural Hull Model Information : 112 ~ 117
5. [학술지(정기간행물)] - 유원선 / 2012 / The implementation of the integrated design process in the hole-plan system / International Journal of Naval Architecture and Ocean Engineering 4 (4) : 353 ~ 361
6. [학술지(정기간행물)] - Suh, H. W. / 2004 / Development of IT based Concurrent Collaboration System / Bulletin of the Society of Naval Architects of Korea 41 (3) : 27 ~ 36
이 논문의 저자 정보
이 논문과 함께 이용한 논문
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2014-550-003430140