지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 발행연도
- 2020.4
- 수록면
- 166 - 172 (7page)
이용수
초록· 키워드
오류제보하기
The microstructure and phase configuration of pure Ti and Ti-6Al-4V GTAW cladding were studied. The cladding microstructures were divided into the base metal (BM) of the substrate, the heat affected zone (HAZ) and weld metal (WM). Depending on the location, the microstructure shape was observed to differ due to heat transfer effects, and the HAZ had a relatively fine structure due to fast cooling of the substrate contact. The lamellar spacing was 5㎛ for HAZ, which is smaller than the 10㎛ of WM. In the pure Ti, the microstructure compositions consisted of a lamellar structure with a pure Ti α phase and a rich Fe β phase, where Fe is an impurity segregated in the β phase. In the Ti-6Al-4V, the microstructure compositions consisted of a lamellar structure with a lean V content of α phase and a rich V content of β phase. The hardness values for pure Ti and Ti-6Al-4V were measured and found to be 425HV and 259HV, respectively.
목차
Abstract
1. 서론
2. 실험 방법
3. 실험 결과 및 고찰
4. 결론
References
참고문헌 (10)
참고문헌 신청
I. Uygur / 2005 / The Effect of TIG Welding on Microstructure and Mechanical Properties of a Butt-Jointed-Unalloyed Titanium, Metalurgija, (Metallurgical) / Metall 44(2):119~123
X. Li / 2005 / Effects of Oxygen Contamination in the Argon Shielding Gas in Laser Welding of Commercially Pure Titanium Thin Sheet / J. Mater. Sci. 40(13):3437~3443
B. Banu / 2012 / Effects of Gas Shielding Flow Rate on Weld Quality of TIG Welding in Ti6Al4V Alloy
A. Karpagaraj / 2014 / The Effect of Process Parameters on TIG Welding of Thin Ti-6Al-4V Sheets / Int. J. Mech. Prod. Eng 2(10):49~52
Y. Lu / 2018 / The Effects of Inter-pass Temperature on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Deposited by Wire Arc Additive Manufacturing(WAAM)
X. Li / 2005 / Effects of Oxygen Contamination in the Argon Shielding Gas in Laser Welding of Commercially Pure Titanium Thin Sheet / J. Mater. Sci. 40(13):3437~3443
B. Banu / 2012 / Effects of Gas Shielding Flow Rate on Weld Quality of TIG Welding in Ti6Al4V Alloy
A. Karpagaraj / 2014 / The Effect of Process Parameters on TIG Welding of Thin Ti-6Al-4V Sheets / Int. J. Mech. Prod. Eng 2(10):49~52
Y. Lu / 2018 / The Effects of Inter-pass Temperature on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Deposited by Wire Arc Additive Manufacturing(WAAM)
함께 읽어보면 좋을 논문
논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!
-
Ti-6Al-4V 레이저 클래딩부에 대한 미세조직 분석
대한용접·접합학회지
2021 .06
-
Microstructure and Mechanical Features of Electron Beam Welded Dissimilar Titanium Alloys: Ti–10V–2Fe–3Al and Ti–6Al–4V
Metals and Materials International
2019 .01
-
Effects of Ti content on microstructure and wear resistance in Ni based WC-Co-Ti cladding layer
대한용접학회 특별강연 및 학술발표대회 개요집
2016 .04
-
Ti-6Al-4V 합금의 미세구조 분석
한국결정성장학회지
2016 .01
-
A Study of Electron Beam Welding Ratios on Dissimilar Titanium Alloys : Ti-10V-2Fe-3Al and Ti-6Al-4V
대한용접학회 특별강연 및 학술발표대회 개요집
2019 .05
-
Determination of Optimal Weld Parameter for Joining Titanium Alloys by Gas Tungsten Arc Welding using Taguchi Method
대한용접·접합학회지
2021 .02
-
Influence of post-heat treatment on the interface-correlated bonding properties of roll-bonded 3-ply Ti/Al/Ti metallic sheets
한국소성가공학회 학술대회 논문집
2021 .11
-
Effect of Volume Fraction of Ti on Microstructure Evolution and Thermal Properties of Al/Ti Laminated Composites
Metals and Materials International
2024 .04
-
Effects of Y and Ti addition on microstructure stability and tensile properties of reduced activation ferritic/martensitic steel
Nuclear Engineering and Technology
2019 .01
-
Ti-Based Solid Solution Carbonitrides Prepared From Ti-Alloy Scraps via a Hydrogenation-Dehydrogenation Process and High-Energy Milling
Metals and Materials International
2015 .01
-
체결용 Ti-6Al-4V 합금의 미세조직 및 기계적/전기화학적 특성에 대한 연구
한국소성가공학회 학술대회 논문집
2022 .05
-
산소함량에 따른 Ti-Al-Fe-Si-O 합금의 기계적 특성 및 미세조직 변화
열처리공학회지
2016 .01
-
A study on deducing optimal heat-treatment condition correlated to the generation of intermetallic compounds at joint interface of a Ti/Al/Ti 3-ply clad sheet
한국소성가공학회 학술대회 논문집
2022 .05
-
Heat treatment for enhancing impact toughness and fatigue cycle of Ti-6Al-4V joint
대한용접학회 특별강연 및 학술발표대회 개요집
2024 .10
-
Microstructure and Refinement Performance of Al-Ti-C Master Alloy: Effect of Excess Ti on the Growth and Nucleating Ability of TiC Particles
Metals and Materials International
2017 .01
-
유한요소법을 이용한 Ti-6Al-4V 의 선삭가공 최적화에 관한 연구
한국CDE학회 학술발표회 논문집
2015 .02
-
Effects of Cr and Fe Addition on Microstructure and Tensile Properties of Ti–6Al–4V Prepared by Direct Energy Deposition
Metals and Materials International
2018 .01
-
Electrochemical and Spectroscopic Study on the Corrosion of Ti–5Al and Ti–5Al–5Cu in Chloride Solutions
Metals and Materials International
2019 .01
-
Ti합금 볼트의 미세조직 및 기계적/전기화학적 물성에 관한 연구
한국소성가공학회 학술대회 논문집
2021 .11
-
Ti-6Al-4V 와이어 적층공정에서 질소 가스의 영향
한국정밀공학회 학술발표대회 논문집
2017 .05
이 논문의 저자 정보
이 논문과 함께 이용한 논문
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2020-581-000580829