지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 저널정보
- 한국고분자학회 폴리머 폴리머 제45권 제6호
- 발행연도
- 2021.11
- 수록면
- 824 - 831 (8page)
- DOI
- 10.7317/pk.2021.45.6.824
이용수
초록· 키워드
오류제보하기
In recent years, research relating to polyurethane has been growing because of the lightness, low cost, and favorable mechanical properties of this material. The increased usage areas of polyurethane in tribological systems make it very important to determine its wear behavior. This study focuses on the wear characterization of polyurethane composites reinforced with glass fiber, SiC, and Al₂O₃. The wear tests were carried out using a pin-on-disc test apparatus against an abrasive counter-face at different applied loads (5 and 10 N). Scanning electron microscopy was used to observe the damage on the worn surfaces. The wear experiments clearly demonstrated that the reinforcement materials significantly affected the tribological properties of the polyurethane composites. In addition, it was observed that particle reinforcement was more effective than fiber reinforcement under experimental conditions. Consequently, polyurethane with glass fiber, SiC, and Al₂O₃ fillers would be a suitable candidate for use in tribological applications.
목차
Abstract
Introduction
Experimental
Results and Discussion
Conclusions
References
참고문헌 (30)
참고문헌 신청
Zmarzły, P.; Gogolewski, D.; Kozior, T. Design Guidelines for Plastic Casting Using 3D Printing. J. Eng. Fiber. and Fabr. 2020, 15, 1-10.
Denoual, M.; Macé, Y.; Le Pioufle, B.; Mognol, P.; Castel, D.; Gidrol, X. Vacuum Casting to Manufacture a Plastic Biochip for Highly Parallel Cell Transfection. Meas. Sci. Technol. 2006, 17, 3134-3140.
Chua, C. K.; Chew, T. H.; Eu, K. H. Integrating Rapid Prototyping and Tooling with Vacuum Casting for Connectors. Int. J. of Adv. Manuf. Technol. 1998, 14, 617-623.
Wortmann, M.; Hoffmann, A.; Frese, N.; Heidi, A.; Brikmann, J.; Brandt, N.; Menzel, M.; Gölzhäuser, A.; Moritzer, E.; Hüsgen, B. Advanced Output of Silicone Molds in Vacuum Casting Processes by Polyamide 12 Powder Supplementation. Polym. Technol. Mater. 2019, 58, 1937-1943.
Jiang, J.; Hu, G.; Li, X.; Xu, X.; Zheng, P.; Stringer, J. Analysis and Prediction of Printable Bridge Length in Fused Deposition Modelling Based on Back Propagation Neural Network. Virtual Phys. Prototyp. 2019, 14, 253-266.
Denoual, M.; Macé, Y.; Le Pioufle, B.; Mognol, P.; Castel, D.; Gidrol, X. Vacuum Casting to Manufacture a Plastic Biochip for Highly Parallel Cell Transfection. Meas. Sci. Technol. 2006, 17, 3134-3140.
Chua, C. K.; Chew, T. H.; Eu, K. H. Integrating Rapid Prototyping and Tooling with Vacuum Casting for Connectors. Int. J. of Adv. Manuf. Technol. 1998, 14, 617-623.
Wortmann, M.; Hoffmann, A.; Frese, N.; Heidi, A.; Brikmann, J.; Brandt, N.; Menzel, M.; Gölzhäuser, A.; Moritzer, E.; Hüsgen, B. Advanced Output of Silicone Molds in Vacuum Casting Processes by Polyamide 12 Powder Supplementation. Polym. Technol. Mater. 2019, 58, 1937-1943.
Jiang, J.; Hu, G.; Li, X.; Xu, X.; Zheng, P.; Stringer, J. Analysis and Prediction of Printable Bridge Length in Fused Deposition Modelling Based on Back Propagation Neural Network. Virtual Phys. Prototyp. 2019, 14, 253-266.
함께 읽어보면 좋을 논문
논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!
-
Recent Development in Polyurethanes for Automotives
Elastomers and composites
2017 .01
-
연마재 작업조건에 따른 폴리우레탄 재질의 마모량 예측에 관한 연구
한국기계기술학회지
2018 .01
-
현무암 섬유 보강 폴리우레탄폼의 열적 성능 및 극저온 환경에서의 기계적 특성 평가
대한조선학회 논문집
2022 .08
-
Glass Fiber and Silica Reinforced Rigid Polyurethane Foams
한국고분자학회 학술대회 연구논문 초록집
2015 .04
-
Synthesis and Application of Self-healing Polyurethane
한국고분자학회 학술대회 연구논문 초록집
2022 .10
-
Synthesis of Azido-thermoplastic Polyurethane and Ester-type Thermoplastic Polyurethane
한국고분자학회 학술대회 연구논문 초록집
2022 .10
-
Characteristics of rigid polyurethane foams prepared with the polyol recovered from polyurethane wastes
한국고분자학회 학술대회 연구논문 초록집
2015 .10
-
Thermal Properties of Polyurethane/Phosphate Composite
한국고분자학회 학술대회 연구논문 초록집
2016 .04
-
폴리우레탄 유압식 왕복 씰의 가속실험
한국트라이볼로지학회 학술대회
2015 .04
-
폐타이어 고무분말과 골재를 혼입한 폴리우레탄 복합재료의 감쇠 특성
한국건설순환자원학회논문집
2020 .09
-
Properties of Polyurethane Nanocomposite Prepared with Functionalized Graphene and Waterborne Polyurethane
한국고분자학회 학술대회 연구논문 초록집
2015 .10
-
Effects of the Surface Treated Silica on the Mechanical Properties for Polyurethane Composite
한국고분자학회 학술대회 연구논문 초록집
2015 .04
-
가속 열 노화 시험을 통한 폴리우레탄 고무스프링의 사용수명 예측
대한기계학회 춘추학술대회
2018 .12
-
2액형 폴리우레탄의 혼합특성에 관한 해석적 연구
한국생산제조학회 학술발표대회 논문집
2017 .04
-
Fully Polyester-Based Thermoplastic Polyurethanes
한국고분자학회 학술대회 연구논문 초록집
2020 .10
-
Recent Progress of Polyurethane-Based Materials for Oil/Water Separation
NANO
2017 .01
-
Structure and Property-focused Examination of Lignin-embedded Thermoplastic Polyurethane Composites
한국고분자학회 학술대회 연구논문 초록집
2024 .09
-
Preparation and Characterization of Waterborne Polyurethane Composite Films Reinforced with Reduced Graphene Oxide
한국고분자학회 학술대회 연구논문 초록집
2018 .10
-
대두유 폴리올을 이용한 환경친화형 폴리우레탄의 합성 및 물성 연구
한국섬유공학회지
2015 .01
-
Thermal insulation and mechanical properties of polyurethane composites with hollow glass microspheres
한국고분자학회 학술대회 연구논문 초록집
2015 .10
이 논문의 저자 정보
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2022-578-000058285