지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 발행연도
- 2017.1
- 수록면
- 193 - 201 (9page)
이용수
초록· 키워드
오류제보하기
The present investigation addresses a new technology, named powder thixoforming, used to fabricate SiCp/ 2024 Al-based composites. The effects of reheating time on microstructure and mechanical properties have been studied. The results indicated that the quantity of liquid, the coarsening behavior of the primary particles, the subsequent plastic deformation occurring during thixoforging, and thus the resulting microstructural compactness and mechanical properties changed as a function of reheating time. The best comprehensive tensile properties of the composite, that is an ultimate tensile strength of 370 MPa and an elongation of 4.4%, were obtained after reheating for 80 min at 625 °C, which was an increase of 23.3% and a decrease of 57.7%, respectively, compared to the 2024 alloy thixoforged under the same conditions as the composite. The fracturing in the composites occurred through interconnecting cracked SiCp and debonded SiC/Al interfaces caused by a higher concentration of stress and a coalescence of microvoids.
목차
등록된 정보가 없습니다.
참고문헌 (23)
참고문헌 신청
함께 읽어보면 좋을 논문
논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!
-
Microstructure Evolution and Tensile Mechanical Properties of Thixoformed High Performance Al-Zn-Mg-Cu Alloy
Metals and Materials International
2015 .01
-
Synergistic Enhancement of the Strength-Ductility for Stir Casting SiCp/2024Al Composites by Two-Step Deformation
Metals and Materials International
2021 .12
-
연속식 가열로용 Level 2 제어시스템 구현
에너지기후변화학회지
2017 .06
-
Investigations into microstructure and mechanical properties of Al 6061/SiCp metal matrix composite spur gear produced via powder metallurgy
Journal of Ceramic Processing Research
2021 .08
-
Neutron Diffraction Study of Phase Stresses in Al/SiCp Composite During Tensile Test
Metals and Materials International
2019 .01
-
Al/SiCp MMC 의 미세홀 가공 조건 선정에 관한 연구
한국정밀공학회 학술발표대회 논문집
2023 .05
-
Strength of Thixoformed A319 Alloy at Elevated Temperature
Metals and Materials International
2021 .01
-
Inconel 706의 열간단조 공정 중 재가열과 변형양에 따른 결정립 미세화에 대한 분석
소성·가공
2023 .10
-
Quadratic magnetoelectric effect of barium titanatecobalt ferrite (0-3) ceramic composite
Journal of Ceramic Processing Research
2020 .01
-
Mechanical Properties of Aluminium Metal Matrix Nanocomposites Manufactured by Assisted-Flake Powder Thixoforming Process
Metals and Materials International
2021 .01
-
Different Tribological Behaviors of SiCp/AZ91 Composites Induced by Tailoring the Distribution of SiC Particles
Metals and Materials International
2021 .01
-
Use of Thixoforming as a Manufacturing Method for Metallic Composites
Metals and Materials International
2020 .01
-
Effect of Ball-Milling Process on Microstructures and Mechanical Properties of Heterostructured 2024Al Alloy Prepared by Powder Thixoforming
Metals and Materials International
2022 .12
-
High-temperature deformation behavior and microstructure evolution of nickel-based superalloy for hot forging
한국소성가공학회 학술대회 논문집
2021 .05
-
A Numerical Analysis of Condensation-Induced Water Hammer in Cold Reheat Pipe
한국전산유체공학회 학술대회논문집
2022 .10
-
금형 재가공 및 재열처리를 통한 페이스리프트 부품용 성형 금형 제작
한국생산제조학회 학술발표대회 논문집
2021 .07
-
제어 시스템을 이용한 재가열로 내 피팅 제품의 열처리 연구
한국생산제조학회 학술발표대회 논문집
2020 .12
-
고강도강 다층 용접금속 재가열부의 미세조직 및 기계적 특성
대한용접·접합학회지
2017 .12
-
연속식 가열로의 Level 2 제어 시스템 설계
시스템엔지니어링학술지
2016 .01
-
DED 공정으로 제조된 Al-B4C 복합재의 미세조직 및 기계적 특성
한국분말야금학회지
2023 .06
이 논문의 저자 정보
최근 본 자료
댓글(0)
0