지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 발행연도
- 2015.1
- 수록면
- 897 - 906 (10page)
이용수
초록· 키워드
오류제보하기
Al-Zn-Mg-Cu alloys are the strongest aluminum alloys which have been widely used for aerospace applications. They are usually machined from the wrought state usually with a high waste percentage. To reduce waste, it is important to thixoform these alloys in near net shape. In this work, the thixoformability of a commercial high performance Al-Zn-Mg-Cu alloy 7075 was studied. A novel multistep reheating regime was developed in recrystallization and partial melting (RAP) route to obtain spheroidal semi-solid microstructures. The as-extruded 7075 alloy was fully recrystallized for a short holding time using the multistep reheating regime. Semi-solid microstructures with fine and spherical solid grains with a grain size of 40-50 μm embedded in liquid matrix were obtained. The advantage of the multistep reheating regimes over those conventional routes was also discussed. Some wheel-shaped components were thixoformed from the as-received 7075 alloy. The ultimate tensile strength, yield strength and elongation to fracture of the thixoformed component based on multistep reheating regime, are 510 MPa, 446 MPa and 17.5% respectively. These values are superior to those of the products manufactured with the conventional RAP route. As the results indicated, thixoforming could be conducted based on commercial extruded Al-Zn-Mg-Cu alloys, which has important practical significance.
목차
등록된 정보가 없습니다.
참고문헌 (26)
참고문헌 신청
함께 읽어보면 좋을 논문
논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!
-
Strength of Thixoformed A319 Alloy at Elevated Temperature
Metals and Materials International
2021 .01
-
항공기 엔진 부품용 고강도 Al-Zn-Mg-Cu계 합금 개발
한국소성가공학회 학술대회 논문집
2024 .10
-
Effects of Reheating Time on Microstructure and Tensile Properties of SiCp/ 2024 Al-Based Composites Fabricated Using Powder Thixoforming
Metals and Materials International
2017 .01
-
Use of Thixoforming as a Manufacturing Method for Metallic Composites
Metals and Materials International
2020 .01
-
Effect of Zinc Content and Cutting Tool Coating on the Machinability of the Al‑(5–35) Zn Alloys
Metals and Materials International
2020 .01
-
유성볼밀링 및 스파크 플라즈마 소결법으로 제조한 Mo-5∼20 wt%. Cu 합금의 열적 특성
전기전자재료학회논문지
2016 .01
-
안정화 열처리에 의한 Al-4.8Zn-1.3Mg계 합금 압출재 특성 평가
한국기계기술학회지
2018 .01
-
Effects of I- and W-Phases Under Identical Conditions on Microstructure and Mechanical Properties of As-Cast Mg?Zn?Y Alloys at Room and Elevated Temperatures
Metals and Materials International
2021 .12
-
Mechanical Properties of Aluminium Metal Matrix Nanocomposites Manufactured by Assisted-Flake Powder Thixoforming Process
Metals and Materials International
2021 .01
-
Microstructure, Mechanical Properties and Tribological Behavior of Two-Phase Mg–Y–Cu Alloys with Long Period Stacking Ordered Phases
Metals and Materials International
2021 .01
-
Improvement of Corrosion Resistance in Cu-Deposited Zn-Mg-Al alloy coated steel
한국표면공학회 학술발표회 초록집
2024 .10
-
Zn-Al-Mg 합금의 압출 공정 시 미세조직 변화에 대한 연구
한국소성가공학회 학술대회 논문집
2023 .05
-
Effects of Interactions Among Alloying Elements on the Microstructure, Phase Transitions, and Electrical Resistivity of the Cu81Al19 Alloy
Metals and Materials International
2022 .08
-
개량 Al-6.5Si 합금의 미세조직, 인장 및 충격 인성에 미치는 합금 원소 첨가의 영향
소성·가공
2020 .06
-
냉간압연가공에 따른 Al-5.5Mg-2.9Si계와 Al-7Mg-0.9Zn계 합금의 압연가공성 및 기계적 특성 차이
한국재료학회지
2016 .01
-
Zn 첨가량에 따른 Al-Si-Mg-Cu계 합금의 미세조직 및 기계적 특성변화
한국주조공학회지 (주조)
2019 .01
-
A356 및 A357 합금으로 용탕단조한 상용차 휠 허브의 미세 조직 및 석출상 변화에 따른 기계적 물성 비교
한국기계기술학회지
2020 .01
-
Mg-5Bi-3Al 마그네슘 고속 압출재의 미세조직과 고주기피로 특성
소성·가공
2022 .10
-
Utilization of Hot Deformation to Trigger Strain-Induced Boundary Migration, Particle-Stimulated Nucleation, and Influence of Nano-Precipitates on Mechanical Properties in High-Alloyed Al–Zn–Mg–Cu Alloys
Metals and Materials International
2024 .08
-
A356 합금 내 미량의 Mg/Cu 첨가 및 열처리조건에 따른 미세조직 및 기계적 성질 변화
한국생산제조학회 학술발표대회 논문집
2020 .12
이 논문의 저자 정보
최근 본 자료
댓글(0)
0